ProMinent ürünleri Türkiye satışı

Pressure holding/overflow valve for mounting directly on the pump dosing head with the functions፦ pressure holding valve, opening pressure approx. 1.5 bar at free outlet, or pre-pressure on the suction side (black rotary knob) - overflow valve, opening pressure approx. 6, 10 or 16 bar* - intake aid when back pressure is pending - Relieving pressure of the pressure line, e.g. during service work - operation via rotary knobs with automatic reset Material: PVDF seals: FPM and EPDM (included) Type: size III Opening pressure: 10 bar* (overflow function) * The overflow opening pressure given here is the pressure at which the valve starts to open. Depending on the type of pump, the pressure may be 50% higher until fully opened. Pressure retaining valves are not absolutely tight shut-off devices.

Applikationen sind z.B. Anwendungen im Trinkwasser sowie Schwimmbad Messgröße: Ozon (O3) Messbereich: 0,02...2,0 mg/l Referenzmethode: DPD4 pH-Bereich: 4,0…11,0 Temperatur: 5...40°C max. Druck: 1,0 bar Anströmung: 30…60 l/h (im Bypass, offener Auslass des Messwassers) Ausgangssignal: 4…20 mA ~ Messbereich temperaturkompensiert, unkalibriert,keine galvanische Trennung Sensorarmatur: DGM oder DLG III Messprinzip: amperometrisch, 2 Elektroden, membranbedeckt Installation im Bypass zur Prozesswasserleitung Verbindung zum Regler über Steuerleitung LiYY 2x0,25 qmm Bestellnummer: 725122 (ist Meterware) (Messleitung nicht im Lieferumfang enthalten) Hinweis: **************** Für die Installation in den Durchlaufgeber DLG III ist ein Montageset Bestellnummer 815079 erforderlich. (nicht im Lieferumfang enthalten) Herkunftsland: DE

Measurement variable: Ozone (O3) Measurement range: 0.02... 2.0 mg/l Reference method: DPD4 pH range: 4.0... 11.0 Temperature: 5... 40°C max. pressure: 1.0 bar Inflow: 30... 60 l/h (in bypass, open outlet of the measurement water) Output signal: 4... 20 mA ~ measurement range temperature-compensated, uncalibrated, no galvanic separation Sensor fitting: DGM or DLG III Measurement principle: amperometric, 2 electrodes, membrane cover

pH sensor for use in aqueous polluted media that contains solids, as well as media with low conductivity. Applications include waste water, cooling water, process water, chemical processes and papermaking. pH range: 1-12 Temperature: 0... 80°C max. pressure: 6.0 bar Conductivity: min 50 μS/cm Screw-in thread: PG 13.5 Electrical connection: SN6 (S8) Sensor shaft diameter: 12 mm Installation length: 120 mm Diaphragm: Dirt-repellent PTFE ring diaphragm Electrolyte: Potassium chloride-containing gel with salt reserve Note: *********** For precise measurements, regular calibration and Adjustment with ProMinent quality buffer solutions recommended!

pH sensor for use in aqueous polluted media that contain a high solids content. Applications include waste water, industrial water, process chemicals, emulsions, suspensions and protein-containing media. pH range: 1-12 Temperature: 0... 100°C max. pressure: 16.0 bar @ 25°C, 6.0 bar @ 100°C Conductivity: min 500 μS/cm Screw-in thread: PG 13.5 Electrical connection: SN6 (S8) Sensor shaft diameter: 12 mm Installation length: 120 mm Diaphragm: annular gap without diaphragm Electrolyte: polymer containing potassium chloride

pH electrode PHEF-012-SE Flat membrane pH sensor for use in aqueous hydrofluoric acid containing media that may contain abrasive solids. Applications include hydrogenic-containing applications in wastewater in the chip industry, in electroplating applications or air washers. pH range: 0-12 Temperature: 0... 50°C max. pressure: 7.0 bar Conductivity: min 150 μS/cm Threaded thread: PG 13.5 Electrical connection: SN6 (S8) Diameter of sensor shaft: 12 mm Installation length: 120 mm Diaphragm: HDPE annular diaphragm flat (Double Junction) Electrolyte: Gel containing potassium chloride

RH -Elektrode RHEP-Au -SE

for use in aqueous contaminated media which contain solids, and media with low conductivity. Applications include wastewater, cooling water, process water, chemical processes and paper making. ORP electrode: platinum Temperature: 0... 80°C max. pressure: 6.0 bar conductivity: min 50 µS/cm Screw-in thread: PG 13.5 Electrical connection: SN6 (S8) Sensor shaft diameter: 12 mm Installation length: 120 mm Diaphragm: Dirt-repellent PTFE ring diaphragm Electrolyte: gel containing potassium chloride with salt stock Note: *********** For precise measurements, a regular validation of the sensor is required recommended with ProMinent quality buffer solutions!