döner lob kompresörleri
Medium air
Volume flow ¹ Q1 m³/min 51.8 28.5
Volume flow ¹ Q1 m³/h 3109 1707
Volume in normal state
Based on T1=273K, p1=1.013 bar, rF= 0% QN Nm³/h 2852 1566
Mass flow kg/h 3722 2044
Suction density ρ kg/m³ 1.197 1.197
Relative Humidity rF% 65 65
Inlet pressure (abs.) p1 bar 1,013 1,013
Outlet pressure (abs.) p2 bar 2.513 2.513
Pressure difference p mbar 1500 1500
Inlet temperature t1 °C 20 20
Outlet temperature t2 °C 143 144
Clutch power Pk kW 120 68
Engine speed nMot min-1 2887 1712
Motor power PMOt kW 160
Motor frequency f Hz 48.5 29
Construction tolerances
for volume/mass flow% +5/-5
for power consumption% +5/-5
Machine noise per unit
Sound pressure level without hood approx. Lp (A) dB (A) 98
Sound pressure level with hood approx. Lp (A) dB (A) 78
measured in free field at a distance of 1 m from the outline of the unit without radiation noises
the pipeline. (Tolerance ± 2 dB (A)). Noise measurement in accordance with DIN EN ISO 2151.
For sound generation at the installation site, see TN01184 (please request if required).
Nominal connection size
Pressure side DN 200
Basic drawing 4000312227 4900057950
Motor data sheet
Type: W22
Manufacturer Aerzen
Model size: 315 S/M
Power: 160 kW
Speed: 2975 min-1
Rated voltage: 400 V
Frequency: 50 Hz
Tolerances: in accordance with IEC 60034-1
Protection class: IP 55
Design: B3T
Insulation class: F
Weight: 1197 kg
Rated current: 266 A
Starting current: 4 to 8 times the nominal current with a direct start
Efficiency: 96.3%
Efficiency class IE4
Power factor: 0.9
Moment of inertia: 3.2 kgm²
Shaft diameter: 65 mm
Start: frequency converter
Motor protection: with 3 built-in thermistors
Drive type: flying over narrow V-belts
Load torque: constant over the entire control range
AERZEN Delta Hybrid
Consisting of the following elements, which are completely assembled in the factory:
Pos. pcs. description
1.1.1 1 AERZEN rotary lobe compressor stage D 62 H
with low pressure rotor profile 3+4 for optimum low energy consumption
with immersion oil lubrication.
1.1.2 1 Torsion-resistant base support with integrated pressure silencer
in accordance with Pressure Equipment Directive PED 2014/68/EU, without absorption material,
with wear-free installations. Motor rocker as a clamping device for
Belt drive, auxiliary spring construction not required Elastic set
machine feet for body-soundproofing installation,
Connection housing with built-in check valve.
1.1.3 1 pressure valve, version B, DN 125, according to PED 2014/68/EU, for protection
of the aggregate, cannot be used as a system safety device,
valve adjustment pressure: 1550 mbar
1.1.4 1 Vacuum generator for transmission room ventilation for 100% oil-free compression
1.1.5 1 Suction filter silencer
ISO Coarse-filter class 60%-85% separation efficiency
in accordance with DIN EN ISO 16890
1.1.6 1 axial compensator DN 200, pressure side
1.1.7 1 Narrow V-belt drive
1.1.8 1 AERZEN AERtronic Advanced control unit
for operating/monitoring a rotary lobe compressor and control
of the optional power cabinet. Control unit integrated in the sound hood. Issuance
Approved to start by the machine or stop in an emergency.
Remote control of the machine via bus and digital communication.
visualization and storage of operating data,
Provision of service, fault and maintenance
Information, navigation and operation via touchscreen. Transfer of all
Parameters and information about standard Modbus RTU interface - without
Power component monitoring.
Operating hours meter, monitoring of windings
temperature of the drive motor with thermistors (PTC), and monitoring of
suction pressure (filter contamination), ultimate pressure, oil pressure and final temperature and
oil temperature.
Basic module and extension modules with digital and analog inputs/
outputs.
The following are included:
Transmitters for suction pressure, end pressure, oil pressure, system pressure
End temperature and oil temperature sensors.
Supply voltage: 3/PE ~ 380 — 420V 50Hz/460V 60Hz
AERZEN Delta Hybrid Type: D 62 H,
as specified above
three-phase motor in accordance with IEC, design: B3T,
160 kW, 2975 rpm, frame size: 315 S/M
Protection class IP 55, 400 V, 50 Hz
Make: WEG, efficiency class: IE4,
insulation class F used in accordance with B,
with 3 built-in temperature sensors
motor assembly
Sound hood made of galvanized steel sheet with
oil drip pan. Painted in RAL 5001/
RAL 7047 front elements. Segmented construction with
inner lining and forced ventilation, electric fan wheel
powered (motor 400V 50Hz/460V 60Hz). Schallhaube
for setting up several units next to each other
suitable. Transport with a forklift is possible.
Sound cover for indoor installation
Extra charge AerTronic extension for
frequency converter
recording the actual value of system pressure with a pressure transmitter or
oxygen content via external transmitter. The target value
Can be entered permanently in the system or via Modbus/
Profibus can be set. Through the external input
Can the speed specification for a frequency converter
can be carried out directly.
I/O extension with analog inputs (4.. 20mA) for
setpoint and an external speed specification.
oil filling, Delta Lube 06
service accessories
Inspection certificate
Certificate 2.2 (Balancing and Material)
